Feeder tape size

Because most placement machine mfgs' feeders vary in width sizes its best to get the reference from them. Like how many 8mm slots does their 16mm consume, and so forth. Std. Sizes I've seen are: 8mm, 12mm, 16mm, 24mm, 32mm, 44mm, 56mm, 72mm, 88mm, 104mm, 120mm & 152mm.

Read more

Here's an example from one mfg:

Number of Feeder Slots Used (Total Available = 64) 8mm & 12 mm 1 1 slot Tape Feeders 16mm, 24 mm, 32mm 1 2 slots 44 mm 1 3 slots 56mm 1 4 slots 72mm 2 5 slots 88mm 2 6 slots 104mm 2 6 slots 120mm 2 7 slots

reply »

 

 

 

 

https://www.rocketscream.com/blog//07/04/picking-the-right-or-wrong-pick-and-place-machine/

 

 

I would like to set the record straight and ask my clients to comment on their experiences.

 

 

If everything went good mostly no customer writing about this.

 

Unfortunately, Lim Phang Mo (Rocketscream) has been experiencing some problems that we are not happy with and are sorry for.

 

This was an old case from where we were trying to resolve the issue.

 

We have sold more than 160 machines with mostly good feedback.

 

Dissatisfied customers are always not good, but I am glad to read that he is happy with his new solution.

 

 

 

Main board went kaput &#; The very moment we installed the vibration feeder that comes with the machine, it started to make a loud noise and that is when we knew something was not right. It turns out that the driver of the vibration feeder located on the main board is damaged and is driving the motor on the vibration feeder well beyond it&#;s maximum rating. SmallSMT told us it was due to the short circuit caused by the vibration feeder metallic body. We find this rather absurd because there was isolation between the vibration feeder electronics and the chassis of the pick and place machine. Anyhow, they sent us a replacement main board albeit it sure looks like a board that has been used before and repaired judging from the amount of flux residue from hand soldering on the new main board.

 

Sometimes shit happened and our customer produced a short of motor PCB against machine chassis. His message &#;motor on the vibration feeder well beyond it&#;s maximum rating&#; is totally wrong because the failure of the main board driver caused by shortage. Why does the replaced mainboard work if the motor was the problem??

 

We have a lot of vibration feeder working under same conditions and received no problems.

 

Even the actual owner of this machine is operating it without problems.

 

What is the truth? This was an early machine construction and in a small space there was not enough distance between PCB and machine plate. Under some conditions and without isolation it could cause a short between machine plate. We changed construction and it never happened again.

 

Even the mainboard received additional fuse in vibration feeder line to prevent these kind of damages

 

We sent out the spare parts in a short time and after installation everything was ok.

 

 

 

North feeder working inconsistently &#; A bulk of our time spent on the machine was on configuring the push feeder. It is at best described as &#;fiddly&#; and &#;inconsistent&#;. It would work perfectly during the setup process, but would then fail to accurately advance the tape of reels during normal operation. This resulted in countless halted job anytime in a pick and place job. But, what baffled us was why it would run almost perfectly on the west feeder but not on the north feeder? We tried every tricks and method suggested by SmallSMT but most of the time it would work fine for a short while before going back to it&#;s old self. We desperately need the north feeder because there is where our components that comes in 12 mm, 16 mm and 24 mm tape width reels can be installed. Even more shocking, SmallSMT told us the 24 mm feeder is actually not supported! Why sold it to us at the first place?

 

&#;what baffled us was why it would run almost perfectly on the west feeder but not on the north feeder&#;

 

Really easy to explain that 8mm feeder lines work more reliable using push feeder than wide 12 / 16 / 24mm plastic tapes. Mostly parts heavier so the tape may slide back if top springs not adjusted strong enough to keep a better friction. But it is always comparing apples with pears a CL feeder 12 /16/24mm is a better solution. That is the reason we focussed on these kinds of feeders and added these even to our smallest machine we are selling now. All other machines using drag feeders have the same problems.

 

 

 

North feeder location not accessible by the head &#; this is one of the most shocking issue we faced on the machine. When we try to move the head to any of the 8 mm tape width feeder on the north side, the software will complain it is not reachable. A solution given by SmallSMT was to shave off a portion of the y-axis limit end stop. We reluctantly shaved off 2 mm from the y-axis limit end stop metal piece. Even though this solved the problem, we start asking our self, isn&#;t the machine calibrated and tested at the factory to detect such issues? Or it was not even calibrated? After the fix, the top camera will no longer park at the machine origin (indicated by a engraved mark on the machine bed) when the homing function is executed. An offset of 2 mm was also needed on the software to tell the machine everything has been moved by 2 mm on the y-axis.

 

If you are looking for more details, kindly visit KF-SMT.

Additional reading:
Swing Check Valve - Diagram, Types, and Applications

This was a real issue caused by a manufacturing problem. The machine head could not move back enough caused by a light barrier switch not installed well. After reducing the length of the metal finger moving inside the light barrier switch the machine worked.

 

We improved our manufacturing process and documented several QE steps by videos since .

 

So, it should be impossible to receive a machine where not all feeder locations tested anymore.

 

 

 

Reel cover tape snapping way too often &#; The machine uses a push feeder (instead of a drag feeder) to advance the component reels. A mechanical cover tape peeling mechanism will pull the cover tape towards the back to expose the component to the pick and place head. How tight or lose the tension on the cover tape can be adjusted to one of the 3 settings on the machine. However, even at the least tight setting, the cover tape on our component reels snap way too often. Again, this resulted in countless stop on the pick and place job.

 

In his case this was our simplest machine he could buy and I told him before he needs a different type of machine but he wanted to buy exactly the simplest one. The funny thing is finally he bought exactly what I introduced a cassette feeder machine.

 

Push feeder are a much better solution than drag feeder because head is not involved in pulling parts tape. There is no mechanical wear out for the head.

 

Drag feeder machines use mostly common winder for a feeder bank so all tapes receive mechanical treatment during feeding process if line addressed or not.

 

Especially this case we tell our customers in any case. So, he knows the limitations of this feeder type. The push feeders are working more reliable than drag feeders and they offer a higher feeder count in smaller space at low price. So, it is ok to accept some limitations.

 

 

 

Some feeder pick up locations are not reachable by the top camera &#; In order to configure the pick up location, we need to move the head manually to the pick up location without vision assistant. This process needs trial & error and we spent a lot of time here. The vibration feeder is one of the location not accessible by the camera on top of few other push feeders.

 

This was small machine and push feeder locations on the front side but camera behind the head.

 

It is logically that we cannot move above the vibration feeder pickup point using the top camera.

 

And it is not a real problem to use the pickup head to move to this position for teach in.

 

 

 

In retrospect, these first machines are no longer in the program and our current machines are better thought out and adapted to the application of prototype production. Where, in addition to a large number of feeders, high precision is also required.

 

Compared to the Huawei Guochang machine used, we are miles away from their production quality and are much more innovative too!

 

We use high-quality imported linear guides and ball screws. The same applies to our servo motors and drivers.

 

We focus on a wide range of applications, which also requires complex software solutions. The whole process from setting up a project to operating the machine is covered here.

 

I also believe that an europe based support is an advantage not to be neglected.

 

We also run a support forum, which none of the other manufacturers mentioned does.

 

And if you need a modular and durable machine that can also be set up in tight office environments, then you've come to the right place.

 

Each machine fits through a standard office door and can be placed there without any problems, as there is no need to plan for a machine weight of 200 to 400 kg.

 

Finally, I can only say that our customers place and 0.35mm pin pitch components and we know that the machines can do it!

 

 

 

Best regards to Phang Moh I think we are still friends!

 

For more Smt Feederinformation, please contact us. We will provide professional answers.